17

2021

-

04

Standard for Urea Quick Connectors


This standard applies to urea quick couplings for connection in urea (SCR) systems using selective catalytic reduction (SCR) technology. The standard defines the standard tip size of the male tube end to ensure the interchangeability of the joint in use.

 

This standard applies to the use of selective catalytic reduction.(SCR)Technology of urea (SCR) Urea quick connector for connection in the system. The standard defines the standard tip size of the male tube end to ensure the interchangeability of the joint in use.

This standard also applies to urea quick couplings used in gasoline, diesel, air delivery systems, or their vapor emission or volatile emission control systems: the maximum working pressure is less6Atmospheric pressure, the maximum negative pressure is less0.6Atmospheric pressure, temperature in the negative45Degree120degree range.

Test content introduction;

ALeak testing process; Leak testing is to ensure that urea quick couplings comply with the most stringent volatile and safety regulations. The details are as follows.

1Application of quick-fit connector70 SMA±7 kPapressure, the leakage rate shall not be greater2cubic centimeter/Minutes.

2Application of quick-fit connector1134 SMA±35 Q7 setThe leakage rate shall not be large.5cubic centimeter/Minutes.

3Application of quick-fit connector60 MPaof negative pressure, the leakage rate shall not be greater2cubic centimeter/Minutes

Before the test, it is necessary to ensure that there is no leakage in the whole pipeline except the tested urea quick-fitting connector. Whether the state is stable can be determined by observing the output curve of the actual leakage rate.

B2. Plug force test process; before the test, the sample should be dry 48 Hours.

1Immerse the test end with the force measuring device and the same shape as the male connectorSAE 30Heavy oil# to the flange.

2Test end 51±5mm/minThe speed of insertion, while measuring the insertion force.

discriminant standard

1The maximum plugging force during the first plugging shall not be greater65N, diameter not less than ≥11mmThe insertion force of the male connector shall not be greater110N.

C2. Pull-out force test; The pull-out force of the quick connector is the maximum force required when the matching pipe end is pulled out from the quick connector. The test process is as follows;

With a force measuring device, apply a tensile load to the test end with the same shape as the male connector until it is completely separated, and measure the tensile force at the same time.

discriminant standard

1The maximum pull-out force of the never-loaded quick connector is not greater470N.

bThe maximum pull-out force of the loaded and unloaded quick connector shall not be greater300N.

D1. Lateral force test; the quick-fitting connector must be able to withstand the lateral force when arranging the hose or pulling the hose. The required specifications are in5/16"and above quick-fitting joints, bearing210NThere shall be no crushing, cracking or bending under lateral load. Specifications In5/16The following shall be determined by mutual agreement.

 

02AL5HiRQEuZjKyvg2yDSA.jpg


04

/

20

News

New factory relocation

Linhai Yongheng Auto Parts Technology Co., Ltd. officially moved to the new factory on March 28, 2024, at 1289 Huifeng South Road, Linhai City

10

/

30

News

"Taizhou Daily" front page headline attention | Jiangnan Street: Industrial Development to Build Binjiang New Town

In the afternoon of August 25, in Dongchang Industrial Park, Jiangnan Street, Linhai City, indoor machines roared and a lively scene.

10

/

30

News

Congratulations on Eternal Auto Parts Technology Passed ISO/TS 16494:2009 System Certification

Linhai City Eternal Auto Parts Technology Co., Ltd. has established a quality management system in line with ISO/TS 16494:2009 technical specifications through NSF-ISR evaluation.

05

/

19

News

SAE quick coupling basic introduction

Quick connector connection and disassembly operation method: Eternal quick connector is composed of connector shell, inner O-ring, outer O-ring, isolation ring, outer retaining ring and self-locking buckle

online message

Welcome to leave a message, leave your valuable comments to us, we will have a technical expert specifically for you to answer!